Problem Uploading Blink to Board Genuino 101

Introduction

The CurieNano is a small development tool based on the Intel® Curie™ module. It is easy to use and perfectly uniform with the Genuino/Arduino 101. The small size allows it to better fit your project's development and cosmos and makes it ideal for wearable tech and small prototypes. The Intel Curie module contains a x86 quark core and a 32bit ARC architecture cadre (Zephyr), integrated Bluetooth 4.0 and half dozen axis attitude sensor. The module's clock frequency is0 32MHZ and the cross tool chain of Intel tin support the development of two cores. The Intel Curie includes dual core storage and users are able to use 196Kb Wink (total 384Kb) and 24Kb SRAM (total 80Kb). It is more than sufficient for near evolution scenarios with the added bonus of Intel'due south strong support network to assist your evolution.

Specification

• Control Fleck: Intel Curie
• BAT Port Power Supply Voltage: 3.5V-6.5V
• 5V Port Voltage: 4.5V-v.5V
• 3V3 Port Voltage: ii.97V-3.63V
• Digital IO Ports: 15 (including four PWM pins D3, D5, D6, D9,)
• Analog IO Input: six
• IO Port DC Bulldoze Current: 20mA
• Integrated Bluetooth 4.0
• Integrated 6 axis accelerometer and 3 axis electronic compass on board, full inertial navigation
• Onboard boost circuit can provide one.5A@5v sensor power supply when using lithium battery supply
• Clock speed: 32Mhz
• Compatible with Arduino IDE 1.6.seven or above
• Bootloader: Arduino/Genuino 101

Board Overview

Function Clarification:

• Onboard D13 LED, ERR and COM low-cal
• Onboard TI TPS61020 boost circuit
• Extended D20 Digital Pin

Tutorial

CurieNano is perfectly compatible with all the features of Arduino/Genuino 101 with the bonus of added features.

Requirements

• Hardware
  • CurieNano x1
  • Micro USB x1
• Software
  • Arduino IDE V1.six.ix Click to Download Arduino IDE from Arduino®

Notation: This is based on the Intel Curie motherboard design. When developing in Arduino IDE you will demand to add information technology'due south extension plug-in. If you have Arduino ane.6.7 IDE or above, you can skip the reload step.

Install Arduino/Genuino 101 Plug-in

Open Arduino IDE, select "Tools" in the menu bar, click "Board" to open the lath manager and install the Intel Curie motherboard programming libraries and drivers.

In the pop-upward window of the board manager observe "Intel Curie Boards by Intel version...", at the lesser left, select the latest version of the "select version", and click on install. When information technology is installed successfully y'all volition see the post-obit image.

After the successful installation of Intel Curie Boards of plug-in and commuter package, y'all should discover Intel Curie in the "Board" menu. You may now program for all based Curie development board.

Annotation: If y'all want to install the driver manually, it is located in your C:\Users\YourUserName\AppData\Local\Arduino15\packages\Intel\tools\arduino101load\i.6.ix ane.24\drivers binder.

CurieNano Instance Programme

In one case you take successfully installed the development surround, programming the CurieNano the same as using an Arduino. The post-obit is a brief tutorial:

• Open Arduino IDE and connect the CurieNano using a MicroUSB cablevision. The arrangement should automatically install Arduino 101 drivers and place CurieNano COM port at the bottom right of the window.

Open the famous "Glimmer" Example programme. Under "Board" select Arduino 101. Under "port" select the corresponding COM port. Finally click "upload" to upload the sample plan.

• If your upload was successful you should see this:

Click to view: [CurieNano(Arduino/Genuino101)Bluetooth, Accelerometer Gyroscope, and Real-Fourth dimension Clock Libraries](https://www.arduino.cc/en/Guide/Arduino101#toc3)

Click to view: [CurieNano Avant-garde Tutorial(Step Count, Shock detection and Centre Rate Monitor,etc.)](https://world wide web.arduino.cc/en/Guide/Arduino101#toc8)

CurieNano Project Evolution

The CurieNano is designed to exist compatible with Arduino 101. Use a 3.7V lithium bombardment-ability to use the Batt interface Curie is ideal for small prototype projects, such as wearables, IoT Bluetooth sensor nodes and robotics projects'''.

Onboard Electronic Compass

HMC5883L/QMC5883 libraries About Library installation.

Download "DFRobot-QMC5883-chief.zip" and unpack it, copy the DFRobot-QMC5883-master binder to the Libraries folder of Arduino and so open Arduino IDE. From "File -> Examples -> QMC5883 -> QMC5883_compass" to open "QMC5883_compass.ino", select your "board" and "port" and upload to the CurieNano in the same way you uploaded the blink sketch.

Wait 5 seconds after the download is complete, open the series monitor port and set the baud charge per unit 9600. Rotate the CurieNano lath and you should see the angle alter.

FAQ

Q&A	Some full general Arduino Problems/FAQ/Tips
Q	Upload stops at "Uploading" process.
A	Some key processes for supporting uploading plan may be blocked by the anti-virus software. Remove blocked processes from the blacklist in your anti-virus software and try again. If that still doesn't solve the problem, reinstall the 101 board support in the "Board Managing director".
Q	Arduino 101 Upload Fail.
A	Arduino 101 Upload trouble

For any questions/advice/absurd ideas to share, please visit the DFRobot Forum or electronic mail techsupport@dfrobot.com

More than Documents

• HMC5883L/QMC5883 Arduino library (Github)

• CurieNano Schematic

• CurieNano JTAG Examination Interface

• HMC5883L Datasheet

• DC-DC Converter Datasheet

• Flash Memory Datahseet

• Inter Curie Datasheet

• TI boost chip Datasheet

Get DFRobot CurieNano - A mini Genuino/Arduino 101 Board from DFRobot Store or DFRobot Distributor.

Plough to the Top

harrisragrand.blogspot.com

Source: https://wiki.dfrobot.com/DFRobot_CurieNano_-_A_mini_Genuino_Arduino_101_Board_SKU__DFR0453

Share this post